ATO Controllers |
12v topoff controllers use a 12v pump or solenoid valve (listed below). If you want to use a 120v pump, you will need a standard or longwire controller.
12v controllers feature a low voltage float switch circuit with removable float switches that have longer wires than our standard controllers. Can be used to control devices up to 5A but only a 1A power supply is included. You need float switches with a JST connector to mate to the controller (listed below). If you'd like to connect your own float switches email us and we can put different float switch connectors on your controller Mounting Brackets Sold Separately! |
|||
 |
12 Volt Single One JST float switch connector, 1A Power Supply |
$30 | |
 |
12 Volt Double Two JST float switch connectors, 1A Power Supply |
$31 | |
Long Wire Float Switches with JST connectors |
|||
 |
LongWire Upper with JST connector 1.5" x 1" x 2"h. 48" leads. Bracket has 2 holes drilled in it for mounting. Email us if you'd like to reverse the bracket so it bends upward instead of downward. |
$11 | |
 |
LongWire Lower with JST connector 1.6" diameter x 1.9" high. 48" leads. Protective surround is open on bottom. Made from 1" PVC with 2 vent holes in the top. |
$11 | |
 |
LongWire Full Surround with JST connector 1.6" diameter x 2" high. 48" leads. Protective surround also has a bottom cover. Made from 1" PVC with 2 vent holes in top/bottom. |
$14 | |
 |
LongWire Skimmer with JST connector 3" stem mounts through 3/8" hole in skimmer cup lid. Secure with a cable tie above and below skimmer lid. 48" leads. Custom length stems available. |
$11 | |
 |
LongWire Combined with JST connectors 1.8" x 2" x 2.25"h. 48" leads. The inverted float switch acts as the fail-safe. Angled plastic bracket includes two float switches and has 2 holes drilled in it for mounting. |
$20 | |
 |
LongWire Horizontal with JST connector 0.7 - 0.8” hole required for mounting (closer to 0.7 is a better fit). Your water level will be permanently set to approx 0.2” higher than the top of the hole. 2.5" extends into tank and 1" on outside of tank. 0.7" float diameter. 18" leads. Switch is closed when the float is straight and open when angled. Can be installed either normally open or normally closed. |
$9 | |
 |
LongWire Jumper Controllers will not operate unless you have float switches connected to all of the controller's float switch connectors. Use this in place of a float switch so the controller will still work. |
$1 | |
 |
LongWire Wire Extension 10 feet long. |
$7 | |
|
LongWire Wire Extension 20 feet long. |
$10 | |
 |
10' LongWire Wire Extension for 2 Float Switches extends two float switches on one extension wire. 10 feet long. White in color. |
$12 | |
|
20' LongWire Wire Extension for 2 Float Switches Extends Two LongWire float switches. 20 feet long. White in color |
$15 | |
12v Pumps and Solenoids |
|||
 |
12v Pump 60GPH, 350mA, 4.2 watts, 12v Female DC Connector, max head 200"/16.4', 5' cord, uses 1/4" ID Tubing, 2.2"x1.4"x1.8". Can be submerged or ran externally. Power supply not included. |
$13 | |
 |
12v Pump & 5' tubing 12v pump and 5 feet 1/4" ID tubing. Power supply not included. |
$15 | |
 |
Normally Closed 12v Solenoid Valve Opens when powered, 12v Female DC Connector. 1/4" or 3/8" Quick Connect Fittings. Collet lock clips included with 1/4" size only. |
$15 | |
|
Normally Open 12v Solenoid Valve Closes when powered, 12v Female DC Connector. 1/4" or 3/8" Quick Connect Fittings. Collet lock clips included with 1/4" size only. |
$17 | |
 |
Normally Closed Stainless Steel Solenoid Valve Opens when powered, 1/4" Ports, 600mA, 7.2 watts, 12v Female DC Connector |
$35 |  |
12vdc power supply 1000mA |
$5 |
 |
12v Power Splitter Allows you to connect two 12v devices to a 12v controller. |
$3 | |